FT-70D on WIRES-X

To connect and control WIRES-X with your FT-70D, you first need to find the room or node numbers you would like to connect to at Yaesu's active Rooms and Nodes pages. All columns can be sorted. e.g. Sort by State to see rooms or nodes in your area.

If you are using a hotspot MMDVM, don't follow these instructions. See the information by Chris, K9EQ about this at hamoperator.com.

CONNECT - To connect to a WIRES-X repeater or node, select the frequency of the repeater or node, then press  MODE  until the DN mode is selected. Connect to WIRES-X by pressing   F   then  AMS .

SELECT - To connect to a room, rotate the  DIAL  until you get to the entry screen  EN # _ _ _ _ _ . Enter the room number and press  AMS 

STORE - After connecting to a room, store the room in one of five memory slots by pressing and holding the corresponding number of  1 ,  2 ,  3 ,  4 , or  5 . A confirmation beep will sound.

CHANGE - To change between rooms stored in memory,  DIAL  to the room and press  AMS .

DISCONNECT - To disconnect from a room, press and hold  BAND . To disconnect from WIRES-X and return to normal radio operations, press and hold  MODE .

If you run into trouble, just disconnect and reconnect to WIRES-X.

And there you have it!

Download the PDF of these instructions.

Blessings!

You're Grounded

Since my "ham budget" is, well... there is no ham budget. So spending big bucks on thick copper busbar, copper mats, copper this, and copper that can get pretty pricey, not to mention a non-negotiable with the wife. This is true especially if it's all prefabricated PnP stuff.

Being like most of you other hams, I like to design and build my stuff myself. In furtherance of this manly, hamly expression of creativity, I designed and built two ground and lightning suppressor boxes, and two interior ground busbars. One set for myself and one set for my friend Stu, KD9MNK. Here is what I came up with.

Busbar in the box with two ATT3G50U's installed

The busbar is constructed with a 1.5 x 1.5 x 0.125" aluminum angle and #10 x 3/4 stainless machine bolts. I drilled 1/4" holes spaced 1.75" apart, allowing for three Alpha-Delta ATT3G50U surge and lightning suppressors to be mounted on the bar, and a heavy ground wire block (top right) for the ground wire. While assembling the busbar, I applied Noalox to all metal surfaces to insure electrical connectivity and prevent corrosion. The exterior bar is housed in a 8 x 8 x 4" PVC junction box with a waterproof cover. The interior and exterior busbars are identical in construction, except for the length - the interior busbar is four inches longer.

The box I made for Stu is fed from the bottom with a 2" PVC conduit running from his home to the back yard where the box is mounted at the base of his antenna. A second 2" opening on the box floor provides the coax exit. this is plugged with a 1/4" thick rubber disk with holes for the coax to pass through. A third exit in the box - also plugged with a rubber disk - is for the cable grounding the busbar and the ATT3G50U's. Water tight. Bug tight. Nice.

The KD9MNK busbar box for the base of the tower

The interior busbar is mounted in the house, just inside the coax conduit feed point. Another set of Alpha-Delta ATT3G50U's reside here, as well as the grounding point for the radios. I designed a 1.25" conduit that passes from the basement, into the wall cavity of the room above, where the KD9MNK station is located. The 20" long conduit terminates into the bottom of a sealed plastic duplex electrical box. A standard blank wall plate holds two SO-239 connections and a grounding stud. Nice and neat. A ground line runs from the wall plate stud to the busbar and out an exit point from the coax conduit, just outside the house. Grounding rods take it from there.

Yup, this should work fine.

The K9KMS busbar box ready for installation at the base of the tower

The KD9MNK interior connectors and grounding stud